Видео

splendid!

can't wait for it in action!!!!!

looking forward to seeing it working.

A very nice bit of kit. Frank

I haven't watched for quite some time. Definitely like your new shop set up. With the gear you have, are you moving away from shoeing horses?

Very nice Gary, well done.

It looks functional, I was told if I purchase this in the states to go ahead and get braided lines and upgrade the gauges. My question is there a follow up video and were you successful using just one burner without damaging the others i.e., backdraft?

Now do you remember

😳 I definitely thought it was going to be a Fox video. Surprise

Nice work Which axis hub and bearings are you using.

Very cool, Gary. Do you live in a rural area ?

Critters!

And feisty, but especially the N American badger. They'll take on a bear and often succeed in chasing it off.

only digging foragers we have around here are skunks and armadillos, those things are huge!

very Nice

Chalk your file when new it will help from getting gaulds

gute idee mit dem plastiksack und dem 2k kleber - sehr dut

I don't know why I'm watching this but it satisfies me.

If it’s ever too tight, I found using a little lube goes a long way. Normally get you decide in there so you can move in and out quite easily.

Great looking feet and great job! Your a talented Ferrier sir!

omg i'm dizzy

bad you for trimming the frog like that

Can you please tell me where to get that handbrake lever kit from? Thanks

Hey Gary. Awesome video and modifications. I have looked at a ton of videos. Looking to save some time now and get it done. Do you have plans for this power hammer available for purchase?

I use on and get razor sharp, mirror finishes on most knives. Also, keep a little spray bottle of water handy for when the stone drys out.

When is the best time then to harvest them to make jam ???

Not many young blokes theses days know to put the wheel under the car for safety reasons. I shutter when I see a young bloke working on his brakes or changing wheel bearings and they are under there vehicle full body or legs and they dont put a wheel under the chassis. If the jack stan or jack fails , I would hate to see the damage.

Typical Land Rover quality and care. We know this part fails and can cause death to the occupants and others but we will did put an a bit of steel plate on, that may stop the axle to completely destroy itself. What a waste of money their vehicle are, not to mention the people that still buy them because it’s a “Land Rover”😅😅.

So the issue is housing failure, which the remedy doesn't actually prevent; it just limits how catastrophic the result is. Since the defect is still present, is LR still on the hook if (when) the failure _does_ occur? Seems to me they owe you a new axle assembly, Gary.

Ha! I have the exact same kind of mask, and have had it for over 20 years. What rods are you using? E6013, E6010 or E7018?

Gary, Nice repair. I sure don’t weld properly and wouldn’t trust my repair in that situation. You usually mostly mig weld. Any particular reason to use arc welding in this case? Best regards Frank (Virginia)

you axcel at welding Gary................

I can smell that burning gear oil from here.

This one was worth a butchers! Nice job Gary ;-)

Nice fix! I don't know much about cars, but why would a snapped axle be leaking oil?

Re: never get old, Beats the alternative Gary :)

typical car manufacturer, we built something that might break, instead of replacing the suspect bit, we will add a catcher so when it breaks it doesn't fall off...

Wow..thank goodness for the landrover fix. Now is the other side ok?

Right, now you are showing off😉 I was impressed with overhead stick already, then you do it left handed. Very impressive, on the floor, outside.

well done ,, I wouldnt have started that without a ramp and a decent mig gun ,,, stick, on your back ,outside ,now thats keen,, but as my grandad used to say , have to makes a hard master.

8:04 hey, the view of that head looks it could be me laying there 😀

Wish my welding looked like that😢

Overhead in situ stick welding, that's not for mere mortals. Nicely done. Thank you for sharing. Wish you well.

Well done Gary. Man if I got down the ground like that, I’m not sure I’d be able to get back up.

Thanks for the reply. Wish me luck 👍😂😂

How do you know when they are ready?

Brilliant video

0:07 зер гут. 0:30

Really good explanations as you demonstrate. 🦾

Nice job, good looking welds.